Contact: Mr. Yang 📞 +86 134 7575 9568 Pioneer of domestic fluff pulp · The most complete fiber portfolio supplier

Home / News / Reading a Fluff Pulp TDS: What Each Number Does on Your Line

Reading a Fluff Pulp TDS: What Each Number Does on Your Line

2026-08-20 · News

Reading a Fluff Pulp TDS: What Each Number Does on Your Line

Most people read a fluff pulp TDS to check whether a grade passes. The more useful question is what happens on the line when a number drifts. This article unpacks each property — what it measures, how it is tested, and what it does to your machine and your product.

The six numbers on a TDS that actually matter

A fluff pulp datasheet typically lists a dozen parameters. Six of them drive forming and finished-product performance: brightness, moisture, freeness, absorbency, bulk and mean fiber length. The rest — ash, extractables, resin content — matter for specific product compliance and cleanliness judgements, and are read when needed.

Each property below answers three questions: what the number measures, which part of the line it affects, and what you see on the floor when it drifts.

Brightness (%ISO): the one the consumer sees

Brightness is measured by ISO brightness and reflects how far the pulp has been bleached. Common bleached fluff pulp sits between 80 and 88 %ISO. Higher brightness gives a whiter-looking core, but it does not improve absorbency directly — chasing maximum brightness can actually increase bleaching chemical consumption, which runs against green production goals.

Keep brightness separate from cleanliness. The first is colour, the second is contamination. Premium products should focus on cleanliness: shives, unbleached specks, foreign matter. Pulp at 84 %ISO with excellent cleanliness usually produces a better-looking core than pulp at 88 with visible impurities.

Freeness (CSF, mL): fluffing energy and fiber integrity

Freeness measures how fast the fiber drains, expressed in millilitres. A higher number drains faster, usually with shorter or more open fiber; a lower number means longer, denser fiber. It is the most engineering-oriented property on the sheet because it maps directly onto hammermill energy.

On the same line, a grade one step higher in freeness often reaches target loft at lower energy — but dust may rise. A grade one step lower gives more intact fiber and a stronger core, at the cost of more refining work. That is why the CSF range is 300–550 mL: it describes adjustment room, not a single promise.

Bulk (cm³/g): the balance point between core height and SAP efficiency

Bulk is the volume a gram of fiber occupies after fluffing. A range of 12–16 cm³/g means that at equal weight, higher-bulk pulp builds a thicker core, which suits thin-core high-absorbency designs; lower-bulk pulp gives a denser core with better compression resistance.

Bulk and SAP carrying are linked. A core that is too open lets SAP migrate and distribute unevenly; a core that is too tight restricts liquid distribution and worsens rewet. The balance point has to be found on the machine — it cannot be calculated on paper.

Absorbency (g/g): what sits behind the 8–12 figure

Absorbency states how many grams of liquid a gram of pulp takes up. The figure is extremely sensitive to test conditions: soak time, liquid type (deionised water or saline), whether pressure is applied, and how the sample is centrifuged all move the result substantially.

So when you see “12 g/g”, the first question is how it was measured. Figures from different suppliers cannot be compared directly; they must be re-tested by one method. We recommend running old and new pulp in parallel under a single laboratory method rather than reading two datasheets side by side — the latter almost always produces the wrong conclusion.

Fiber length distribution: the underrated stability indicator

Mean fiber length gives you one number, but the distribution decides actual behavior. A high long-fiber share builds core integrity and compression resistance; a high short-fiber share fluffs easily and gives a more uniform surface, but generates more dust.

Typical mean length is 2.0–2.6 mm for softwood grades and 1.6–2.4 mm for blends. What really matters is whether the distribution is stable between batches — a shift in distribution often signals a problem earlier than a change in the average. That is why we suggest adding fiber length distribution to incoming-lot sampling.

Moisture (%): static and storage behind the ≤10% limit

Moisture looks like the least interesting figure and is the most frequent source of floor problems. Too much moisture and the fiber cakes, flows poorly and meters unevenly. Too little and static becomes obvious — dust flies and material hangs up.

≤10% is the industry’s standard upper control limit. In practice many lines find their sweet spot between 7 and 9%, depending on workshop humidity and the static elimination capability of the forming machine. If winter static is a recurring issue, it is worth confirming the available ex-mill moisture options with your supplier.

Property Typical range Main effect What you see when it drifts
Brightness %ISO 80 – 88 Core appearance Low: grey cast; high: no practical gain
Moisture % ≤10 Flowability, static High: caking and blockage; low: dust
Freeness CSF mL 300 – 550 Fluffing energy, dust High: more dust; low: higher energy
Absorbency g/g 8 – 12 Acquisition, retention Low: worse rewet; unusually high: verify method
Bulk cm³/g 12 – 16 Core height, SAP carrying Low: stiff core; high: collapse risk
Mean fiber length mm 2.0 – 2.6 Core integrity Short: weaker core, more dust
Hongbo pulp laboratory testing
Batch-by-batch laboratory testing: brightness, moisture, freeness, absorbency, bulk and fiber length distribution

Using the table to set your own acceptance window

Do not copy the typical values from a TDS. Work backwards from your own line data: first establish how the current pulp actually behaves on your machine, then set the limits from there. The optimal window for the same grade can differ by 20 mL of freeness or more between two lines.

One principle when setting windows: tighten the properties that matter most to the finished product, loosen the rest. Brightness and moisture can usually be relaxed; freeness and bulk should be tight because they drive fluffing behavior and core structure. A window that is too wide is not a standard at all, and one that is too narrow cannot be supplied consistently — it only adds cost.

A TDS is not a certificate of conformity, it is a map. It tells you roughly which direction the material will travel; where it lands on your line is something only your own trial data can mark.

In one sentence: six numbers, six effects. Read a TDS in this order — freeness and bulk first (can it fluff, will the core stand up), then absorbency and fiber length (absorption and strength), and brightness and moisture last (appearance and day-to-day running).

About Hongbo Pulp

Shandong Hongbo Pulp & Paper Co., Ltd. focuses on fluff pulp across seven fiber families — bleached, natural, bamboo, pure softwood, softwood/hardwood blend, poplar/pine CMP and reed pulp — supplied in unprocessed, semi-processed and fully processed grades. A dedicated research team and field application engineers support more than 200 hygiene manufacturers from fiber selection and on-line trials through to volume supply.

Media & Sales Contact

Mr. Yang · Tel/WeChat +86 134 7575 9568 · yang@hongbopulp.com. For grade-specific TDS, samples or on-line trial support, submit a request through the contact page — we reply within one business day.

Related Articles

Ready to Try Hongbo Fluff Pulp?

Free samples and grade-specific TDS within one business day